Free Shipping Icon

Free shipping in USA (lower 48 states), Canada (almost free) & EU

How to Sketch a Soft-Bottom Swim Entry for Mat Sizing

Before you choose a mat size, sketch the part of your swim entry you want to use. Show how you reach it from shore, where you want room to stand, and anything the layout must work around. Add measurements you already know and mark the rest as unknown.

A sheet of paper with a few clear labels gives LakeMat a useful starting point for discussing the soft area. It also helps separate the area you want to use from the whole stretch of lakefront.

Start with the moment you want to improve

Think about a normal trip into the water. Where do you step in? Where do you pause to adjust a float or put your sandals down? Where would you like room to stand before swimming?

Those may be different places. A narrow route from shore and a wider standing area make a different sizing question from one broad patch directly in front of the beach.

Write a short purpose such as “Room to stand at our existing swim entry” at the top of the page. Keep dock supports, boat lifts and watercraft launches out of that request unless they are part of the project you want assessed. Equipment support raises its own product and site questions.

Draw the shore, the route and the standing area

Make a simple overhead sketch. Put land at the bottom and the lake above it. Draw the shoreline, then add the route people already use to reach the intended standing area.

Outline that area separately. Use a dashed line to mark the area you want to discuss with LakeMat. Add nearby features that affect the space: a dock corner, steps, a seawall, large rocks or an existing boat route.

Use the sketch to check whether the area you want supported connects sensibly to the place you enter. A rectangle farther out may miss the awkward part near shore. Equally, the entire waterfront may be much more area than you are trying to improve.

Do not draw over a property line as though the space is yours to use. If a boundary or shared-access arrangement is uncertain, label it for confirmation.

Label width and length in plain language

For every dimension you can supply, show its direction. “Width across the standing area” is more useful than an unexplained number in the corner. “Distance out from the entry point” is a different measurement from water depth.

Use feet or meters consistently. Write “approximate” beside an estimate and identify an existing measurement you trust. If you cannot establish a dimension safely from land or existing records, leave it blank for an appropriate site assessment.

This is a planning exercise from shore. Do not wade into cold water, step onto ice or test a soft bottom to complete the drawing. An honest question mark is useful information.

Label the directions and symbols so another person can follow the drawing.

W: width across the desired standing area.

L: distance from the entry point toward its far edge.

Dashed outline: desired use area, not a product outline.

Question mark: a dimension or condition still to be checked.

Keep bottom conditions separate from water depth

Write down what you already know about the bottom from previous use or a documented assessment. For example, you may know that the usual entry feels firm near shore but soft farther out. Mark where that change has been observed, without extending the label to places you have not checked.

A photograph can show a dock, visible plants and the shoreline. It cannot establish how much support the bottom provides. Leave uncertain firmness, submerged obstacles and changes in slope as questions.

MuckMat is designed to provide a supported walking surface over soft, mucky bottoms. That intended use makes the location of the soft area relevant to sizing. It does not mean the largest visible patch of water is the right footprint, or that a mat changes the water depth. If the product category is still uncertain, the mat selector can help organize that first question.

Use the sketch to discuss a layout

Use the finished page to open the sizing conversation. Ask LakeMat to confirm the current model, outside dimensions and suitable layout for the conditions shown. Do not assume that an old article's size table describes the version currently offered in your market.

If the desired area bends around a feature or seems to need more than one mat, ask how that arrangement would be handled. Leave joining details and edge placement for product-specific guidance. The installation resources provide the next layer of instructions once the product and layout are confirmed.

Check local rules before committing to coverage

A useful sketch can also help explain the proposed activity to your local authority. Requirements depend on the location and purpose. Michigan's invasive-species permit guidance says a permit is required for benthic barriers used to manage aquatic weeds, and local governments may have additional requirements. Minnesota DNR's aquatic plant regulations list preventing aquatic plant growth with lake-bottom barriers among activities not allowed in public waters.

Ask your state or local authority to review the location and proposed use before choosing a final footprint or buying for installation.

Bring a clear question to the sizing conversation

Keep the sketch, one overview photo and your notes together. Include the lake's location, the purpose of the area, dimensions with units and the items marked unknown. If the contact form cannot take an attachment, describe the project and ask how best to share the drawing.

Then ask LakeMat about swim-entry sizing. Show where you enter, where you want room to stand, and what still needs checking.